Peningkatan Kualitas Pengajaran Gambar Teknik Melalui Pelatihan Solidworks Bagi Guru Sekolah Menengah Kejuruan Muhammadiyah Kabupaten Banyumas

Muhammad Muryanto; Trio Nur wibowo; Syaukaty Yasinta; Muhammad Ramadhani S. L; Irfauji Firman Hidayat

doi:10.35960/pimas.v4i2.1852

Authors

Muhammad Muryanto UNIVERSITAS MUHAMMADIYAH PURWOKERTO
Trio Nur wibowo Universitas Muhammadiyah Purwokerto
Syaukaty Yasinta Universitas Muhammadiyah Purwokerto
Muhammad Ramadhani S. L Universitas Muhammadiyah Purwokerto
Irfauji Firman Hidayat Universitas Muhammadiyah Purwokerto

DOI:

https://doi.org/10.35960/pimas.v4i2.1852

Keywords:

Technical Drawing, CAD Training, SolidWorks, ISO Standards, Muhammadiyah Vocational Schools

Abstract

Technical drawing training based on ISO standards using SolidWorks is a strategic step to enhance the competencies of vocational high school (SMK) teachers, particularly in aligning the learning process with industrial needs. This community service activity aimed to provide practical knowledge and skills to SMK Muhammadiyah teachers in Banyumas Regency regarding internationally standardized technical drawing (ISO 128, ISO 5456, ISO 7200) and its implementation through parametric Computer-Aided Design (CAD) software, namely SolidWorks. The training methods included lectures, hands-on practice, group discussions, pre-tests, and post-tests. The pre-test results showed that the participants' average score was only 47.5, indicating a low level of understanding of technical drawing standards and the use of SolidWorks. However, after the training, the average score increased significantly to 79.6, reflecting a 67.5% improvement. These findings demonstrate that training based on hands-on practice and case studies can effectively enhance teachers' technical competencies. This program also strengthens the role of teachers as agents of change in vocational education based on Industry 4.0 technology. It is hoped that this activity will be followed by advanced training sessions, such as motion simulation and stress analysis using CAD.

References

Afnison, & Alwi, R. (2020). Peningkatan Kompetensi Guru dalam Menggunakan SolidWorks pada Pembelajaran Desain Teknik. Jurnal Pendidikan Teknik Mesin, 8(2), 101-110.

Duran, M., & Garcia, C. (2020). University and Vocational High School Collaboration in Technical Education: A Model for Sustainable Development. International Journal of Vocational Education and Training.

Geng, F., Li, J., & Zhang, C. (2020). Effect of CAD-Based Learning on Students’ Engineering Design Capabilities. International Journal of Engineering Education, 36(4), 1220–1230.

Górski, F., Wichniarek, R., & Zawadzki, P. (2019). Teaching Technical Drawing and CAD in Accordance with Industry 4.0 Requirements. Advances in Science, Technology and Engineering Systems Journal, 4(3), 91–97.

Pradana, S., & Ekawati, D. (2022). Analisis Kebutuhan Pelatihan Gambar Teknik Berbasis Komputer di SMK. Jurnal Pendidikan Vokasi dan Teknologi, 3(1), 45–53.

Wahyudi, A., & Wibowo, H. (2020). Pemanfaatan Software CAD untuk Meningkatkan Kualitas Pembelajaran Gambar Teknik di SMK. Jurnal Pengabdian Masyarakat Teknik, 1(2), 33–40.

Zainul, M., & Nugraha, R. (2018). Pentingnya Standar ISO dalam Pembelajaran Gambar Teknik untuk Menunjang Kompetensi Lulusan SMK. Jurnal Pendidikan Teknologi dan Kejuruan, 21(1), 15–23.

Fauzi, A., Subekti, H., & Wahyudi, A. (2021). Islamic Education Values and Vocational Training: Building Character in Technical Education. International Journal of Educational Development..

Hsiao, S. W., Lin, C. Y., & Lu, H. P. (2019). Constraint-Based Parametric Modeling in CAD Systems for Efficient Design Communication. Computers in Industry.

Kim, D., & Lee, Y. S. (2018). Drawing Standardization for Manufacturing and Its Role in Engineering Communication. Journal of Engineering Design and Technology.

Khan, A., Ahmad, R., & Ali, A. (2017). Impact of Pre-Test and Post-Test Design on Learning Outcomes in Technical Training Programs. International Journal of Training and Development.

Liu, Q., Zhang, L., & Wang, C. (2020). Standardization in Engineering Drawing and Its Influence on Product Lifecycle Management. Procedia Manufacturing.

Nguyen, T., Ikeda, M., & Tsuji, H. (2018). Utilizing Pre-assessment to Customize Technical Training Content for Adult Learners. Journal of Learning and Instruction.

Shih, R. H. (2021). Parametric Modeling with SolidWorks. SDC Publications.

Zhang, Z., Feng, Y., & Wang, J. (2020). 3D Assembly Modeling and Simulation for Engineering Design Education. International Journal of Mechanical Engineering EducationIranian Women: An Application of the Health Belief Model. J Canc educ , 1-10.

Sunil, T., Hurd, T., Deem, C., Nevarez, L., Guidry, J., Rios, R., et al. (2014). Breast Cancer Knowledge, Attitude and Screening Behaviors AMong Hispanics in South Texas Colonias. J Community Health , 39 (DOI 10.1007/s10900-013-9740-7), 60-71.

Taylor, D., Bury, M., Campling, N., Carter, S., Garfield, S., Newbould, J., et al. (2007). A Review of the use of the Health Belief Model ( HBM ), the Theory of Reasoned Action ( TRA ), the Theory of Planned Behaviour ( TPB ) and the Trans-Theoretical Model ( TTM ) to study and predict health related behavior change February 2007 ( Draft for C. NHS .